Home > High Cpu > Cisco Router High Cpu Interrupts

Cisco Router High Cpu Interrupts

Contents

SNMP query of the flash file system on the switch. Use this handle in the show pds client packet last sink command. Refer to Cisco Catalyst 3750 Series Switches Release Notes for the list of release notes for Catalyst 3750 Switches. Depending on the model and the type being used this can range from 5 to 40% If the switch is stacked then, at a minimum, the CPU will operate normally a have a peek at this web-site

show ip route summary Shows the number of route entries used by each protocol. Multicast Listener Discovery (MLD) snooping (TTL = 1) This traffic is indeed destined to the router. If the root cause of the high CPU utilization is a Layer 2 loop, the spanning tree configuration could be the problem. Step 2: Determine the CPU Queue that Causes the High CPU Usage Condition The Cisco Catalyst 3850 Series Switch has a number of queues that cater to different types of packets

Cisco Router High Cpu Interrupts

For example, Queue 0 in this output corresponds to rpc in the previous output;. Documentation of the configuration and operation of software features is generally publicly available, and therefore configuration problems can often be diagnosed without the need for direct assistance from the vendor or For example, this is the output of the netdr capture, which shows that the IPv4 TTL is 1: Source mac 00.00.50.02.10.01 3644 Dest mac AC.A0.16.0A.B0.C0 4092 Protocol 0800 4094 Interface Gi1/8

Figure 2 – High CPU Utilization Troubleshooting Methodology on Catalyst 4500 Switches The general troubleshooting steps are: Issue the show processes cpu command in order to identify the Cisco IOS processes The redundant router normally drops this traffic, because it has arrived on the wrong interface and therefore fails the RPF check. The Meta-data is for internal use by the system, but the Data output provides actual packet information. Ip Input High Cpu This table explains the output fields.

Additionally, if you poll several different objects in the same object group/table and get the error message, is not unusual because of this same reason. Hulc Led Process High Cpu The continual update of baseline CPU utilization can be necessary as you add more configuration to the network setup or as your network traffic pattern changes. With the configuration of such protocols, a higher CPU utilization is normal. Runs protocols and processes that provide network control Examples include Spanning Tree Protocol (STP), Cisco Discovery Protocol (CDP), VLAN Trunk Protocol (VTP), Dynamic Trunking Protocol (DTP), and Port Aggregation Protocol (PAgP).

Switch#show platform health %CPU %CPU RunTimeMax Priority Average %CPU Total Target Actual Target Actual Fg Bg 5Sec Min Hour CPU Lj-poll 1.00 0.02 2 1 100 500 0 0 0 1:09 Cat4k Mgmt Lopri High Cpu One option to resolve this issue is to reduce the volume of encrypted traffic (re-route traffic or limit the flows that are encrypted). You must manually prune the ports with non-Cisco IP phones. From this output, you can see that the K2CpuMan Review process, a job to handle CPU-bound packets, uses up the CPU: Switch#show platform health %CPU %CPU RunTimeMax Priority Average %CPU Total

Hulc Led Process High Cpu

Packets that are sent to the CPU for processing Examples include: Routing protocol updates BPDUs An intentional or unintentional flood of traffic Packets that are sent to the CPU for forwarding This rate control helps prevent denial-of-service attacks. Cisco Router High Cpu Interrupts This results in high CPU. Show Memory Usage Cisco Each queue has some reserved memory in hardware to hold packets for the queue so that one queue or packet type cannot use all the available memory.

All packets received on icmp-q are the same. Check This Out These scenarios can cause heavy CPU usage by the SNMP engine system process: Multiple servers simultaneously performing an SNMP query. Restore redunancy. Enter the command several times. How To Check Bandwidth Utilization On Cisco Router

Step 1: Check for the Cisco IOS process with the show processes cpu command. Step 4 exit Exit the CLI. disable Disable port monitoring sc0 Set span on interface sc0 Source module and port numbers Source VLAN numbers Note:For Optical Services Modules (OSMs), you cannot perform a SPAN capture http://justjoomla.net/high-cpu/wuauserv-high-cpu.html Known symptoms that can occur when the switch CPU is too busy: Spanning-tree topology change—When a Layer 2 network device does not receive timely spanning-tree BPDUs on its root port, it

See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments insccisco Mon, 10/28/2013 - 21:01 I just tried following this exact advice Cisco Fed Process Step 3 logging buffered 128000 Enable system message logging to a local buffer, and set the buffer size to 12800 bytes. Disable console logging on the router with the no form of the logging console command.

The switch does not support route-map deny statements for PBR.

Use the information in Table 1 and the conclusion that you drew in Step 1. Recommendations The supervisor engine CPU utilization does not reflect the hardware forwarding performance of the switch. As more tasks are being offloaded to those microcontrollers there is an increase in communication between the CPU and the microcontrollers. Arp Input High Cpu Router#monitor session 1 destination interface 3/2 Now, go to the SP console.

The show processes cpu command tells you whether these packets are regular traffic packets or control packets. We'll send you an e-mail containing your password. You can use the output of the show processes cpu history privileged EXEC command to determine normal operating baseline utilization for the previous 72 hours. http://justjoomla.net/high-cpu/w3wp-exe-high-cpu-iis.html Also IP broadcast packets.

We recommend that you use the switch console for debugging CPU utilization issues. Broadcast suppression is disabled by default. The Supervisor Engine 720 with PFC3 supports the rate limit of packets that are redirected to the MSFC for ACL and VACL logging. Note: There are two ASICs: 0 and 1.